[Free] 2018(Aug) Ensurepass VMware 2V0-622 Dumps with VCE and PDF 51-60

Ensurepass.com : Ensure you pass the IT Exams
2018 Aug VMware Official New Released 2V0-622
100% Free Download! 100% Pass Guaranteed!

VMware Certified Professional 6.5 – Data Center Virtualization

Question No: 51

Which three operations can cause VMFS metadata updates? (Choose three.)

  1. Restarting a VM using the guest OS.

  2. Launching a VM console.

  3. Migrating a VM with vMotion.

  4. Powering a VM on or off.

  5. Expanding a VMFS datastore.

Answer: C,D,E Explanation:

Metadata is updated each time you perform datastore or virtual machine management operations. Examples of operations requiring metadata updates include the following:

Question No: 52

Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)

  1. Disconnect ESXi host from vCenter.

  2. VMware Tools are installed in the virtual machine.

  3. Ensure that the system hardware complies with ESXi requirements.

  4. Back up the host.

  5. Check the interoperability of any other software integrated with vSphere.

Answer: C,D,E Explanation:

As is logical for any software update, first backup the host. The check to ensure system hardware compatibility according to ESXi requirements. You also need to check interoperability of software integrated with vSphere.

Question No: 53

What counter should an administrator check to determine if a virtual machine is ballooning?

  1. swapinRate

  2. vmmemctltarget

  3. swapped

  4. vmmemctl

Answer: D

Question No: 54

What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)

  1. Assign shares and limits to VM virtual disks.

  2. Assign shares and limits to datastores.

  3. Assign shares and limits to Storage DRS clusters.

  4. Assign shares and limits using VM storage policies.

Answer: A,D

Question No: 55

What is the correct way to replace the certificate on an existing vCenter Server that is part of a vCenter HA configuration?

  1. Put the vCenter HA in Maintenance mode, replace the certificate, exit Maintenance mode.

  2. Shut down Passive and Witness nodes and replace the certificate on the Active node.

  3. Remove the Passive and Witness nodes, replace the certificate, reconfigure the cluster.

  4. Replace the certificate while all nodes are participating in the cluster.

Answer: C

Question No: 56

An administrator cannot enable multi-processor Fault Tolerance (SMP-FT) for a virtual machine.

Which are two possible causes for this? (Choose two.)

  1. The virtual machine is running on a vSAN datastore.

  2. The Fault Tolerance network is using a 10Gbit uplink.

  3. The virtual machine has 6 vCPUs assigned.

  4. The virtual machine has a 1TB VMDK attached.

  5. The virtual machine has snapshots present.

Answer: C,E Explanation:

The following vSphere features are not supported for fault tolerant virtual machines.

Snapshots. Snapshots must be removed or committed before Fault Tolerance can be enabled on a virtual machine. In addition, it is not possible to take snapshots of virtual machines on which Fault Tolerance is enabled.

Licensing

The number of vCPUs supported by a single fault tolerant VM is limited by the level of licensing that you have purchased for vSphere. Fault Tolerance is supported as follows:

vSphere Standard and Enterprise. Allows up to 2 vCPUs vSphere Enterprise Plus. Allows up to 4 vCPUs

Question No: 57

In a vSphere environment, two resource pools are created as shown in the Exhibit.

Ensurepass 2018 PDF and VCE

Each VM is configured with 1 GB of memory. When the administrator tried to power on VM3, the operation failed.

What action in the resource pool settings will allow VM3 to power on successfully?

  1. Deselect Expandable Memory Reservation

  2. Increase Memory Reservation

  3. Deselect Expandable CPU Reservation

  4. Increase the CPU Reservation

Answer: B Explanation:

VM3 doesnt have sufficient memory to power. So in resource pool settings, increase CPU reservation of VM3 and it will power up.

Question No: 58

Which command can be run to troubleshoot connectivity problems with vmkernal network interfaces?

  1. esxcli network

  2. vmkping

  3. net-status

  4. vicfg-vmknic

Answer: B Explanation:

The vmkping command sources a ping from the local VMkernel port.

Question No: 59

Storage capabilities be populated in what two ways? (Choose two.)

  1. The administrator can use tags to describe capabilities.

  2. Default capabilities are provided by vCenter Server.

  3. Datastores can advertise their capabilities through VAAI.

  4. Datastores can advertise their capabilities through VASA.

Answer: A,D

Question No: 60

Which iSCSI initiator type can be used with any network interface card?

  1. Software iSCSI initiator

  2. Software FCoE adapter

  3. Hardware Independent iSCSI initiator

  4. Hardware Dependent iSCSI initiator

Answer: A Explanation:

Software iSCSI Adapter

A software iSCSI adapter is a VMware code built into the VMkernel. It allows your host to connect to the iSCSI storage device through standard network adapters. The software iSCSI adapter handles iSCSI processing while communicating with the network adapter. With the software iSCSI adapter, you can use iSCSI technology without purchasing specialized hardware.

100% Ensurepass Free Download!
2V0-622 PDF
100% Ensurepass Free Guaranteed!
2V0-622 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *

Proudly powered by WordPress